Skip to content
Main -> And -> How to Install an Icemaker . how-tos . DIY
  • 17.12.2018
  • by Gajind
  • 2 comments

How to Install an Icemaker . how-tos . DIY

How to Disconnect Refrigerator Water Line/Hose

The first step is to run the water line. Drill a hole behind the refrigerator, and then one underneath the sink. Go down into the crawl space. Feed the line down, and then up through the refrigerator hole. Whenever drilling holes for water lines, always be sure to use a paddle bit that's one to two sizes larger than the water supply line to prevent the line from kinking.

Tighten the fittings as needed, using channel-type pliers or an adjustable wrench.

Refrigerator ice and water hook up

If you don't have a convenient water supply pipe and valve near the refrigerator, you must instead find another spot to hook up the water line. Usually, this will be at some other existing water hookup point, like the water supply lines connected to your sink faucet or dishwasher. An Adapt-a-Tee is an ideal plumbing fitting for this purpose.

Adapt-A-Tees are easy to install, and they provide the extra line you need with the least amount of work. The type designed for copper pipe uses simple compression fittings, and there are other types designed for attachment to CPVC or PEX water supply pipes.

Adapt-a-Tees can be used in many situations where you need an extra line. They come in various sizes to suit whatever situation you have.

You will also need a longer flex water supply tube to run from the water pipe to the refrigerator. Measure the distance carefully, and buy a supply tube with plenty of length for the job.

First, locate the shutoff valve under the kitchen sink where you want to connect the new water line. Shut off the water at the valve that controls the cold-water supply pipe to the faucet. If there are no fixure shutoff valves, you can turn off the water by closing the main water supply valve to the entire house.

The tee adapter connects to the water supply shutoff valve. Wrap threads on the cold water valve with two or three wraps of thread-seal tape.

How to Hook Up a Water Line to a Refrigerator From the Sink

Twist the male end of a quick-tee adapter onto the valve. Wrap the female thread on the opposite end of the adapter with thread-seal tape.

Twist the faucet supply line onto the female end of the adapter. Slip the compression nut that came with the kit over the newly installed supply line. Make sure the threads are facing the end of the line. Thread the ferrule from the kit onto the new line.

A refrigerator with an automated ice maker and a built-in water dispenser does absolutely nothing if you do not have a water line to connect to it. Having a refrigerator with a water and ice dispenser is very convenient. To get the best performance, connect the water supply line. There is a chance that you. bellasoulshop.com: Water Line Hookup and Installation Kit for Refrigerators and Ice Makers: Kitchen & Dining.

Wrap the remaining male threads on the quick-tee adapter with thread-seal tape. Insert the new water line into the opening on the tee.

Slide the compression nut over the male threads and tighten it on the adapter. Tighten all three nuts on the quick-tee adapter with pliers or an adjustable wrench. Do not twist the nuts too tight as this could damage the supply valve, the supply line and the adapter. Place the end of the water line you intend to connect to the refrigerator into a 5-gallon bucket.

Turn the cold water supply valve on beneath the sink. Let 1 or 2 gallons of water run through the new line to remove the air. Turn off the supply line.

How To Connect A Water Line To Your Refrigerator (+Tips & Tricks) - GOT2LEARN

This will control the water flow and water pressure to the refrigerator. Be sure to put a gasket seal between the valve and the T-fitting.

Feed the line down, and then up through the refrigerator hole. Now that the water line has been run to the refrigerator, it's time to do what's called the . screws to secure the unit to the freezer wall, and then add the ice bucket under the kit.

Attach the free end of the copper tubing to the valve. Now the refrigerator is connected. Clamp any tubing inside the cabinets along the back of the cabinets, to keep it in place. Turn on the water supply.

Connecting a water line for a refrigerator icemaker and water Running a water line to a refrigerator to supply its ice maker and drinking water. Imagine the convenience of having cold water or ice cubes any time you want them -- no more filling up pitchers to keep in the refrigerator or waiting for ice cube. Here is a step-by-step water line installation refrigerator guide. A new refrigerator with a water dispenser and ice maker needs to be hooked up.

You should have cold water very shortly. You will have to wait hours before you have ice.

Voshakar

2 thoughts on “How to Install an Icemaker . how-tos . DIY

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top